/*
 * Copyright 2010 by egnite GmbH
 *
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 *
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 * 3. Neither the name of the copyright holders nor the names of
 *    contributors may be used to endorse or promote products derived
 *    from this software without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
 * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
 * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
 * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
 * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
 * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
 * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF
 * THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
 * SUCH DAMAGE.
 *
 * For additional information see http://www.ethernut.de/
 */

/*
 * \file arch/arm/board/at91sam9260_ek.c
 * \brief AT91SAM9260-EK initialization.
 *
 * \verbatim
 * $Id$
 * \endverbatim
 */

#include <toolchain.h>

#define PHY_STRAP_AD0       _BV(PA14_ERX0_A)
#define PHY_STRAP_AD1       _BV(PA15_ERX1_A)
#define PHY_STRAP_AD2       _BV(PA25_ERX2_B)
#define PHY_STRAP_AD3       _BV(PA26_ERX3_B)
#define PHY_STRAP_AD4       _BV(PA28_ECRS_B)

#define PHY_STRAP_TESTMODE  _BV(PA17_ERXDV_A)

#define PHY_STRAP_RMIISEL   _BV(PA29_ECOL_B)

#define PHY_STRAP   ( \
    PHY_STRAP_AD0 | PHY_STRAP_AD1 | PHY_STRAP_AD2 | PHY_STRAP_AD3 | PHY_STRAP_AD4 | \
    PHY_STRAP_TESTMODE | PHY_STRAP_RMIISEL )


/*!
 * \brief Delay loop.
 *
 * \param Number of loops to execute.
 */
static void Sam9g45ekDelay(int n)
{
    int l;

    for (l = 0; l < n; l++) {
        _NOP();
    }
}

/*!
 * \brief Enable peripheral clocks.
 */
static void Sam9G45ekClockInit(void)
{
    outr(PMC_PCER, _BV(PIOA_ID));
    outr(PMC_PCER, _BV(PIOB_ID));
    outr(PMC_PCER, _BV(PIOC_ID));
    outr(PMC_PCER, _BV(EMAC_ID));
}

/*!
 * \brief Toggle external hardware reset line.
 */
static void Sam9260ekReset(void)
{
    /* Set reset pulse length to 250us, disable user reset. */
    outr(RSTC_MR, RSTC_KEY | (2 << RSTC_ERSTL_LSB));
    /* Invoke external reset. */
    outr(RSTC_CR, RSTC_KEY | RSTC_EXTRST);
    Sam9g45ekDelay(250);
    /* Wait until reset pin is released. */
    while ((inr(RSTC_SR) & RSTC_NRSTL) == 0);
    Sam9g45ekDelay(25000);
}

/*!
 * \brief Initialize the PHY hardware.
 *
 * On startup all GPIO pull-ups on the SAM9 are enabled by default
 * and may fight against internal pull-downs of the DM9161A. Here
 * we switch off all pull-ups connected to PHY strap pins and
 * issue an external reset.
 */
static void Sam9G45ekPhyInit(void)
{
    /* The PHY needs 25ms for powering up. */
    Sam9g45ekDelay(250000);
    /* Disable pull-ups. */
#if 0
    outr(PIOA_PUDR, PHY_STRAP);
    outr(PIOA_ODR, PHY_STRAP);
    outr(PIOA_PER, PHY_STRAP);
#endif
    /* Toggle reset line. */
    Sam9260ekReset();
    /* Re-enable the pull-ups. */
    // outr(PIOA_PUER, PHY_STRAP);
}

/*!
 * \brief Early AT91SAM9260-EK hardware initialization.
 *
 * This routine is called during system initalization.
 */
void NutBoardInit(void)
{
    Sam9G45ekClockInit();
    return;
    Sam9G45ekPhyInit();
}